M&P can make custom Fluorosint Machined Parts to your specifications or drawings.
We have a plastic machine shop; Fluorosint® is one of the plastics we can use to make parts.
FLUOROSINT MATERIAL DESCRIPTION
Fluorosint® is a proprietary mixture in which synthetically manufactured mica is chemically linked to polytetrafluoroethylene (PTFE).
This bonding results in properties not normally attainable in reinforced PTFE.
Fluorosint® grades offer an excellent combination of low frictional properties and dimensional stability.
Fluorosint® is only produced by Quadrant Engineering Plastic Products.
It offers excellent chemical resistance and continuous use temperature of 500°F (260°C).
Compared with PTFE, it has higher load carrying capability, 1/9 of the deformation under load, and a lower coefficient of thermal expansion.
GRADES OF FLUOROSINT
Fluorosint® 500
Fluorosint® 500 has nine times greater resistance to deformation under load than unfilled PTFE.
Its coefficient of linear thermal expansion (CLTE) approaches the expansion rate of aluminum and is 1/5 that of PTFE — often eliminating fit and clearance problems.
Fluorosint® 500 is non-abrasive to most mating materials.
It is 1/3 harder than PTFE, has better wear characteristics, and maintains low frictional properties.
Fluorosint® 207
Fluorosint® 207’s unmatched dimensional stability, excellent creep resistance, and WHITE color uniquely position this material to serve FDA regulated applications.
It is non-permeable in steam and complies with FDA regulation 21 CFR 175.300.
Its relative wear rate is 1/20 the rate of PTFE below 300°F (150°C).
CUSTOM MACHINED PARTS
M&P makes Fluorosint® Machined Parts in a completely controlled environment.
Some Examples of parts we can machine from Fluorosint®:
Fluorosint O-rings, Fluorosint Seats, Fluorosint Bushings, Fluorosint Bearings, Fluorosint Guide Blocks, Fluorosint Wear Pads, Fluorosint Washers.
Fluorosint® is a registered trademark of Quadrant Engineering Plastic Products.
M&P can make custom Fluorosint Machined Parts to your specifications or drawings.
We have a plastic machine shop; Fluorosint® is one of the plastics we can use to make parts.
FLUOROSINT MATERIAL DESCRIPTION
Fluorosint® is a proprietary mixture in which synthetically manufactured mica is chemically linked to polytetrafluoroethylene (PTFE).
This bonding results in properties not normally attainable in reinforced PTFE.
Fluorosint® grades offer an excellent combination of low frictional properties and dimensional stability.
Fluorosint® is only produced by Quadrant Engineering Plastic Products.
It offers excellent chemical resistance and continuous use temperature of 500°F (260°C).
Compared with PTFE, it has higher load carrying capability, 1/9 of the deformation under load, and a lower coefficient of thermal expansion.
GRADES OF FLUOROSINT
Fluorosint® 500
Fluorosint® 500 has nine times greater resistance to deformation under load than unfilled PTFE.
Its coefficient of linear thermal expansion (CLTE) approaches the expansion rate of aluminum and is 1/5 that of PTFE — often eliminating fit and clearance problems.
Fluorosint® 500 is non-abrasive to most mating materials.
It is 1/3 harder than PTFE, has better wear characteristics, and maintains low frictional properties.
Fluorosint® 207
Fluorosint® 207’s unmatched dimensional stability, excellent creep resistance, and WHITE color uniquely position this material to serve FDA regulated applications.
It is non-permeable in steam and complies with FDA regulation 21 CFR 175.300.
Its relative wear rate is 1/20 the rate of PTFE below 300°F (150°C).
CUSTOM MACHINED PARTS
M&P makes Fluorosint® Machined Parts in a completely controlled environment.
Some Examples of parts we can machine from Fluorosint®:
Fluorosint O-rings, Fluorosint Seats, Fluorosint® Bushings, Fluorosint Bearings, Fluorosint Guide Blocks, Fluorosint Wear Pads, Fluorosint Washers.
Fluorosint® is a registered trademark of Quadrant Engineering Plastic Products.